Betty the Commer Pizza Truck Project.
- Thread starter Leerec
- Start date
These engines weren't fitted with proper stem seals just 'O' rings that were supposed to stop oil from going down the bores when the engine is idle optimistically called 'sealing rings' in the manual. Not very effective and but better than nothing and should be included in the head set. Just looked at the head set on aBay and they can be seen in pairs in the bore holes in the gasket.
yeah i did see those and think they just looked mega small and different to what i had seen online, thanks buddy, taking the head to the brother in law tomorrow and hes going to teach me how to sort it all out and do any machine work needed so shes looking like shes saved
Thought I’d update you, heads fine! Somehow it’s gone in, through the valve, out the other end without even hitting it! Then landed flat In the piston area. I’m a Lucky man!
Also. The eBay gasket set you linked, they are based literally a 20 min drive from me, drove down today to collect it to save faff with postage and waiting, tomorrow I’ll put new rings on the valves and then Wednesday onwards I’ll be putting her back together !
Hopefully by Saturday she’ll be running again!
Need to hunt a new dizzy and potential coil but might do that later down the line as I now know how to get to all that fairly easily.
Been a wild few days
Gasket Peoples contact details below if you ever need them. They stock tons and were a lovely bunch, most is NOS stock too
Attachments
Starting to come back together now! A clean table so the Roast dinner is on for Sunday!
Gave her a push in 4th gear and the valves and rocker gear all moving correctly with no lock ups which is promising.
The gasket set, the thermostat cover bit didn’t fit so need to make one for that. The rest of the gasket kit was spot on for anyone wondering.
Next week I can get back to building the gas box for the rear then need to get the dizzy valve clearances and timing sorted then she should be good to go!
Gave her a push in 4th gear and the valves and rocker gear all moving correctly with no lock ups which is promising.
The gasket set, the thermostat cover bit didn’t fit so need to make one for that. The rest of the gasket kit was spot on for anyone wondering.
Next week I can get back to building the gas box for the rear then need to get the dizzy valve clearances and timing sorted then she should be good to go!
Attachments
Betty is fully back together and running!
Well, she’s running pretty bad, the vacuum hose basically snapped off on my hand so I’ve had to plug it at the carb and dizzy for now just to get her fired up. Got some new stuff coming Saturday hopefully.
In other news my thermostat seems to have a leak. It’s pretty corroded so I’m thinking just order a new one to save the hassle .
Well, she’s running pretty bad, the vacuum hose basically snapped off on my hand so I’ve had to plug it at the carb and dizzy for now just to get her fired up. Got some new stuff coming Saturday hopefully.
In other news my thermostat seems to have a leak. It’s pretty corroded so I’m thinking just order a new one to save the hassle .
Attachments
So update, 4th cylinder I am getting a spark but its not firing. When i pull the lead off the engine doesnt change, does with all the other cylinders, unsure if its Valve clearance on that cylinder or a compression issue, deffo getting some compression just from the finger test but tomorrow I will re-do all the valves, then check compression and fit a new advanced vacuum hose as my one snapped whilst i was taking it all apart. I'm praying its something simple.
Tried the plug swap, still cylinder 4, tried the leads too, so I’m hoping ive done the valve clearance too tight on the 4th cylinder.
Will re-do them all again tomorrow. The do a compression check. Pray for me I don’t want to have to have the head off again
Well guys, its looking like I need a new piston. My question is, what size pistons fit well in my setup, I have an Su carb job done on the manifold and she was running lovely before nutgate happened. I dont mind having to get stuff rebored or honed, if you were in my shoes and had a 1974 1725 iron head, what would you do, im thinking 4 new pistons but unsure what size is best and at the moment I havent got the damaged piston out so size wise im unsure whats in it until i get some daylight this week and get to it. Any suggestions welcome, apart from fit a V8 