[:X] You spoil me [:X]
well Sybhil any way
[}][8D]
Sybhil & no1
well Sybhil any way
[}][8D]Sybhil & no1
chris's new ride
- Thread starter commerchris
- Start date
valves
carb manifold
head
Sybhil & no1
carb manifold
head
Sybhil & no1
the valves have had anti-reversion grooves machined in, and i waisted the stems and put a 60 degree backcut on the inlet seats for better flow
the red thing is a short ram pipe of the correct shape to give an extra 6.7% airflow. just need to sort a suitable k&n filter
and the finished head, skimmed .079" (2.02mm)
getting close now [8D]
"you were only supposed to blow the bloody SLIDING doors off"
the red thing is a short ram pipe of the correct shape to give an extra 6.7% airflow. just need to sort a suitable k&n filter
and the finished head, skimmed .079" (2.02mm)
getting close now [8D]
"you were only supposed to blow the bloody SLIDING doors off"
looking good[8D]
Cheers
Jules
RatSport www.ratsport.co.uk
Cheers
Jules
RatSport www.ratsport.co.uk
shiney in it [}][^]
Sybhil & no1
[}][^]Sybhil & no1
nice nice nice
Thanks guy's
the cylinderhead has just left the building[}]
Sybhil & no1
the cylinderhead has just left the building
[}] Sybhil & no1
I hope it's heading your way Chris :I
http://www.commervanspares.co.uk/
http://www.yorkshireclassiccampers.co.uk/
http://www.commervanspares.co.uk/
http://www.yorkshireclassiccampers.co.uk/
Ha Ha it was going towards sybhil in the opposite direction to me [}]
Sybhil & no1
in the opposite direction to me [}]Sybhil & no1
its nearly ready
had to give the bodywork some ball pain in the filter area, and make the filter endplates, the shed yeilded some 7075 t6 aircraft alloy [8D]
just need to make a cable bracket, attach the exhaust, change the oil and test run
"you were only supposed to blow the bloody SLIDING doors off"
How cool is that The Mini abutment plate makes it so much easier to sort out the cables.
I tried unsuccessfully to get Harvey running this evening[V] A good spark and there's fresh petrol fed from a can but all I got was a few bangs from the exhaust and a little bit of burbling. Got the battery on charge and will have another go in about half an hour - the neighbours love me really
'Harvey the RV'
The Mini abutment plate makes it so much easier to sort out the cables.I tried unsuccessfully to get Harvey running this evening[V] A good spark and there's fresh petrol fed from a can but all I got was a few bangs from the exhaust and a little bit of burbling. Got the battery on charge and will have another go in about half an hour - the neighbours love me really
'Harvey the RV'
i begrudge paying £25 for a piece of sheet metal with 5 holes [V] so i will make a nice stainless bracket
sure you have it timed right and the HT leads on the right cylinders [?]
"you were only supposed to blow the bloody SLIDING doors off"
sure you have it timed right and the HT leads on the right cylinders [?]
"you were only supposed to blow the bloody SLIDING doors off"
You can get them cheaper - I got mine for a tenner with two gaskets and the clip for the choke cable, but you are right - I just couldn't be a***d. One thing I realised is that there isn't a vacuum take-off for the dizzy, could I use the connection that normally connects to the Mini crank case breather.
Set timing roughly by usual method and double checked the leads - I'll check again though [V]
'Harvey the RV'
Set timing roughly by usual method and double checked the leads - I'll check again though [V]
'Harvey the RV'
do you mean vacuum for the dizzy [?] if so take it from the carb, the large diameter spout is the one we are using on sybhil
"you were only supposed to blow the bloody SLIDING doors off"
"you were only supposed to blow the bloody SLIDING doors off"
no problem trev, there is already 3 holes in them
"you were only supposed to blow the bloody SLIDING doors off"
"you were only supposed to blow the bloody SLIDING doors off"